DECKING
INDUSTRIAL ALLUMINIUM DECKING
Industrial Aluminium Decking is available in two different types, Solid & Open Mesh. Both Solid & Open Mesh Deckings are designed and manufactured to withstand a UDL of up to 7.5Kn/Sq.m.
The material used for the manufacture of the deckings is Aluminium Alloy 6082 T6 which has high tensile and excellent corrosion resistance properties.
Where the trench structure shape varies abruptly, or a presence of any protruding pipework or instrumentation access holes through the Decking may occur, the Decking can be specially cut as per the exact shape and size.
The material has good machinability & weldability properties. Openings required on the deckings will be banded or welded with stiffeners of the same material to provide additional strength.
Maximum weight of a single panel should not exceed 40 Kgs for the ease of installation. T-Key slots are also provided on the Decking for the ease of removal in case of any maintenance required.
The top surface of the decking is fully serrated providing better foot grip for operatives.
All Aluminium Deckings are supplied in an Anodized AA20-AA25 finish, which prevents the risk of corrosion due to highly corrosive gases (H2S) and moisture.
Anodising preserves the original surface texture and guarantees product durability for many years.
Decking is available in both 30mm & 40mm Depth profiles.
TECHNICAL SPECIFICATION
PICTURES
INDUSTRIAL ALUMINIUM SEALED ODOUR CONTROL DECKING
Industrial Aluminium Solid Odour Control Decking(OCD) is an excellent choice for areas which has dangerously high levels of H2S and other highly corrosive effluents. OCD is designed and manufactured to withstand a UDL of up to 7.5Kn/Sq.m.
The material used for the manufacture of the deckings are Aluminium Alloy 6082 T6 which has high tensile and excellent corrosion resistance properties.
The deckings are equipped with pre-installed side profiles which accommodate a special 5mm thick EPDM Foam Rubber Strip around the perimeter of the decking which provides a total seal and excellent odour/water control capability.
An Aluminium flatbar is also provided & fixed on to the underside of Decking between two panels to sandwich the EPDM Rubber Strip on areas where there are no supports in order to provide maximum performance of the odour control system.
Where the trench structure shape varies abruptly, or a presence of any protruding pipework or instrumentation access holes through the Decking may occur, the Decking can be specially cut as per the exact shape and size.
The material has good machinability & weldability properties. Openings required on the deckings will be banded or welded with stiffeners of the same material to provide additional strength.
The clearance gap between any protrusions and the Decking can be sealed by using a 5mm thick EPDM Rubber Sheet (cut to size on site), and fixed to the decking using an aluminium gasket frame.
Maximum weight of a single panel should not exceed 40 Kgs for the ease of installation. T-Key slots are also provided on the Decking for the ease of removal in case of any maintenance required. The top surface of the decking is fully serrated providing better foot grip for operatives.
All Aluminium Deckings are supplied in an Anodized AA20-AA25 finish, which prevents the risk of corrosion due to highly corrosive gases (H2S) and moisture. Anodising preserves the original surface texture and guarantees product durability for many years. Decking is available in both 30mm & 40mm Depth profiles.
TECHNICAL SPECIFICATION
PICTURES
INDUSTRIAL GMS DECKING
Industrial GMS Decking is designed and manufactured where specified. Capable of a much heavier load capacity than aluminium or where there is a requirement for high-density traffic.
The standard decking consists of load-bearing bars @ 30mm centers & cross bars @ 100mm centers and the material used is Steel grade S275 JR, Steel grade S355 JR is also available.
Comprising of a series of parallel flat load bearing bars stood on end equispaced, with either indented round or square twisted bars, which are resistance welded into the top surface of the load bearing bars, primarily to keep them upright.
In the event there is a requirement for openings within the decking areas, or there is a presence of any protrusion through the decking, the Decking can be specially cut as per the exact shape and size.
Openings required on the deckings will be banded or welded with stiffners of the same material to provide additional strength.
Maximum weight of a single panel does not exceed 40 Kgs for the ease of installation.
The Deckings are available in Galvanized finish.
TECHNICAL SPECIFICATION
PICTURES
